McCormick, Theresa M.

Density functional theory (DFT) calculations are useful to model orbital energies of conjugated polymers, yet discrepancy between theory and experiment exist. Here we evaluate a series of relatively straightforward calculation methods using the standard Gaussian 09 software package. Five calculations were performed on 22 different conjugated polymer model compounds at the B3LYP and CAM-B3LYP levels of theory and results compared with experiment. Chain length saturation occurs at approximately 6 and 4 repeat units for homo- and donor–acceptor type conjugated polymers, respectively. The frontier orbital energies are better approximated using B3LYP than CAM-B3LYP, and the HOMO energy can be reasonably correlated with experiment [mean signed error (MSE) = 0.22 eV]. The LUMO energies, however are poorly correlated (MSE = 0.59 eV), and we show that the molecular orbital energy of the triplet state gives a much better estimate of the experimentally determined LUMO level (MSE = −0.13 eV).

Electron-deficient π-conjugated polymers are important for organic electronics, yet the ability to polymerize electron-deficient monomers in a controlled manner is challenging. Here we show that Ni(II)diimine catalysts are well suited for the controlled polymerization of electron-deficient heterocycles. The relative stability of the calculated catalyst–monomer (or catalyst-chain end) complex directly influences the polymerization. When the complex is predicted to be most stable (139.2 kJ/mol), these catalysts display rapid reaction kinetics, leading to relatively low polydispersities (∼1.5), chain lengths that are controlled by monomer:catalyst ratio, controlled monomer consumption up to 60% conversion, linear chain length growth up to 40% conversion, and ‘living’ chain ends that can be readily extended by adding more monomer. These are desirable features that highlight the importance of catalyst design for the synthesis of new conjugated polymers.

We have synthesized a series of cyclopentadithiophene–benzochalcogenodiazole donor–acceptor (D–A) copolymers, wherein a single atom in the benzochalcogenodiazole unit is varied from sulfur to selenium to tellurium, which allows us to explicitly study sulfur to selenium to tellurium substitution in D–A copolymers for the first time. The synthesis of S- and Se-containing polymers is straightforward; however, Te-containing polymers must be prepared by postpolymerization single atom substitution. All of the polymers have the representative dual-band optical absorption profile, consisting of both a low- and high-energy optical transition. Optical spectroscopy reveals that heavy atom substitution leads to a red-shift in the low-energy transition, while the high-energy band remains relatively constant in energy. The red-shift in the low-energy transition leads to optical band gap values of 1.59, 1.46, and 1.06 eV for the S-, Se-, and Te-containing polymers, respectively. Additionally, the strength of the low-energy band decreases, while the high-energy band remains constant. These trends cannot be explained by the present D and A theory where optical properties are governed exclusively by the strength of D and A units. A series of optical spectroscopy experiments, solvatochromism studies, density functional theory (DFT) calculations, and time-dependent DFT calculations are used to understand these trends. The red-shift in low-energy absorption is likely due to both a decrease in ionization potential and an increase in bond length and decrease in acceptor aromaticity. The loss of intensity of the low-energy band is likely the result of a loss of electronegativity and the acceptor unit’s ability to separate charge. Overall, in addition to the established theory that difference in electron density of the D and A units controls the band gap, single atom substitution at key positions can be used to control the band gap of D–A copolymers.

A series of eight polymers based on the parent structure, poly[2,6-(4,4-bis-(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b′]-dithiophene)-alt-4,7-(2,1,3-benzothiadiazole)] (PCPDTBT), were synthesized for a systematic group-14 and group-16 single atom substitution study. The eight polymers were constructed with C/Si/Ge and S/Se/Te varied in the donor and acceptor, respectively. By examining experimental spectroscopic data and DFT calculated geometry and electronic structure, we gain new physical insights into the effects of heavy atom substitution at different positions in a donor–acceptor polymer. Absorption and emission experiments demonstrate that group-14 substitution in the donor unit only slightly blue shifts the long wavelength absorption (HOMO to LUMO transition) and that group-16 substitution in the acceptor affects this absorption to a much greater extent. Solvatochromism experiments show that the charge transfer excited state is most polarized when the acceptor contains a lighter atom and is influenced very little by the atom in the donor. Changing the atom in the acceptor has less effect on the absorption of the Si-donor and Ge-donor polymers than the C-donor polymers. Polymers that contain C-donors are stronger light absorbers than their Si-donor and Ge-donor analogues regardless of which atom is in the acceptor position. These results clarify the effects of single atom substitution on donor–acceptor polymers and aid in the future design of polymers containing heavy atoms.